Once upon a time there were two little girls…
Who loved to giggle and loved to twirl!
One of my best remembered pleasures of childhood was having a twirly skirt to twirl in, how about you? Thanks to the terrific talent of two of my Baby Lock educator friends – Sue Kostroski and Missy Billingsley – I discovered the wonderful ruffling foot for my Baby Lock serger. I knew a twirly skirt was in my future for sure! (Okay, be honest, am I too old for one now? Ha!)
This foot is awesome. Do you have one? I’m pretty sure that other sergers have ruffling feet too, but Baby Lock’s got me spoiled. Not only can I blow my threads through the threading mechanism (look ma, no tweezers and scary words outta my mouth), but the feet SNAP on and off. How cool is that? Spoiled, yep, I know it. Anyway, if you happen to have a serger that has a ruffling foot, you can make this project too – just keep in mind that the photos show Baby Lock’s Ovation serger and BLE8-RF Ruffling Foot. Check your machine manual for the settings you will need.
Choose your fabric! I picked several different prints from Riley Blake Fabrics.
You can use Jelly Rolls if you have some getting dusty in your sewing room, or you can cut your own as I did. I used the same fabric to complete an entire row in the skirts shown here, but the rows don’t need to be the same fabric – just mix and match as you please! You’ll need approximately 38 – 40 strips of fabric cut on the straight grain; each strip should be either 2.5″ (Jelly Roll width) or 3″ wide and as long as the width of the fabric.
The skirt in the photo directly above was made with 2.5″ wide strips, and the blue toned skirt shown further above was made with 3″ wide strips.
Here’s the chart for a skirt that fits a tall three- to four-year-old:
Row 1: 1 strip
Row 2: 2 strips
Row 3: 3 strips plus about 12”
Row 4: 6 strips less about 10”
Row 5: 10 strips less about 6”
Row 6: 15 strips plus about 22”
(Add more rows for a taller child and lessen the number of rows for a shorter child.)
Keep in mind that your stitch length and how much tension you put on the fabric as it feeds into the foot may change how tight your ruffles are. Usually – for a 2 to 1 ratio ruffle – you would need to double the number of strips for each consecutive lower row, but I discovered that it took less than that. It may be the way I was holding the fabric, but I think it had something to do with the weight of all the fabric as the skirt grew. You may want to have extra strips prepared, just in case you need them.
Serge the strips in each row together (short end to short end) to make one long strip for that row. A four-thread overlock works nicely.
Serge the first (single strip) row along one long edge. Narrow hem or narrow roll hem the last row along one long edge.
Got a narrow hem foot? This is the PERFECT time to use it! (See this foot in action on my Instagram pages!)
You definitely want to hem this last row before you begin. (Ask me how I know that! Ha!) Makes for a pretty hem, doesn’t it?
Arrange the fabric strip rows in order on your table.
Pop on your ruffling foot and follow the directions found in the package with the foot to set up the machine correctly for ruffling. (Watch Pam Damour’s demo of this sweet foot HERE. She’s got lots of good tips for machine settings, etc.!)
The ruffling foot works by serging two strips together while gathering the one underneath the foot. To begin, insert Row 2’s strip RIGHT SIDE UP under the foot. (I found it helpful to raise the foot, gently tug up the toe of the foot and push the fabric under it.) Then put Row 1 into the slot on top of the ruffling foot WRONG SIDE UP with the finished serged edge on the left.
Crank the fly wheel a few times to take a few stitches to secure the two rows of strips together. Then go for it! As you ruffle, take care that you do not hold back on the fabric, especially the fabric under the foot. Also, don’t go so fast that you wander over into the fabric strip. Try not to cut off more than a whisker as you serge. You want to let the feed dogs do the work so the ruffles form prettily. (I’ve posted a clip of this foot in action on my Facebook page, in case you want to watch!)
Add Row 3. Remember that this one will be RIGHT SIDE UP under the foot with Row 2’s ruffle WRONG SIDE UP in the slot on top of the ruffling foot.
You will need to straight stitch (on your regular sewing machine) along the top of each row of serging to secure the ruffles nice and firmly. You may choose to attach all the rows and then sew those lines of stitching, but I find it easier to do it as you go… that’s why we have swivel chairs!
Repeat the process, row by row, until you are finished. The final row you add will be the narrow hemmed row. Make sure you have that piece under the foot with the narrow hemmed edge on the left.
If some of your rows don’t end up flush with the one above or below, just whack it off evenly along that side. Don’t worry – your skirt will still be plenty full!
Measure around your child’s waist and subtract one inch. Then cut a piece of 1.5” or 2” wide elastic to match this length. (Why subtract an inch? You will want a snug fit since this skirt has a bit of weight to it. Just be sure it’s comfortable for your little dancer!)
You can find pretty colors of wide elastic now, which is cool. Riley Blake Fabrics has added some wide elastic to coordinate with their fabrics (woo-hoo!). Find it at many fine retailers. Farmhouse Fabrics also has a nice line of wide elastics perfect for waistbands.
Mark the top edge of the skirt to divide it into 8-10 equal parts. Then divide the elastic into the same amount of equal parts. Pin the elastic to the skirt, right sides together, so that the skirt is distributed evenly on the elastic according to the marked divisions.
Serge the elastic to the skirt, gently stretching the elastic as you serge from marked point to point to fit the two together neatly. You may want to turn the blade to the down position so you don’t cut off any elastic.
Now you are ready to serge up the seam at the back of the skirt! A four-thread overlock works great. Align the ends of the elastic and each row of ruffles down to the hem. Pin right sides together and serge the skirt back seam.
At your sewing machine, sew along the serging to further secure the seam. Fold the seam allowance of the elastic over to one side, neatly tucking the serge tail beneath it, and top stitch in place to secure. Do the same for the seam allowance at the hem.Sweet little blossom! You can see why I call this the carnation skirt! 🙂
This was so fun I had trouble stopping – just wanted to keep making them! Here’s hoping that you’ll have as much fun as I did with this skirt project and that your little sweeties will have a blast swirly twirling. Click HERE to watch a fun video showing the steps in action to make this skirt by Lydia Maria of Telafante!
Till next time, thanks for reading!
Like the flower headbands? That’s another blog project – click HERE to check it out!
Photos by Amber Purcell